Scene-dock notes: the square tiles cut the rigging tags off the sides
The scene dock keeps a wall of square tiles, one for each flown piece, so a rigger can point at a photograph instead of describing a tag that is already thirty feet up. The tiles have to be square or they will not sit in the painted grid we already have on the dock door. Last Tuesday a volunteer made a new set from the photographs I had taken on the floor, and almost every tile lost the rigging tag. The painted surface of the piece was nicely centered. The tag at the side, where we write the cue number and the house mark, had been cut off by the square.
That is a smaller problem than it sounds until a cue is late and someone at the door is trying to match a still to the piece on the bar. The photograph is not there as a beauty shot. It is there as a record of a particular flown piece, and the tag is how we tell two similar flats apart. If the square keeps the paint and discards the tag, I have a handsome grid of unlabelled scenery. I had already printed the sheet and taped it to the door. I had to do it again.
The photographs were not square to begin with. I had shot them wide, so that the tag on the right stile, and a little of the neighboring piece, would stay in the frame. The volunteer, trying to be helpful, had dropped each wide shot into a square by cutting from the center. That is the obvious way to fill the frame. It is also the way the side margin disappears. The tag lives at the edge. A center crop treats the edge as leftover.
What I needed was a square that kept every part of the subject, including the lettering on the tag. The method is not complicated. I placed each wide photograph onto a larger square canvas and let the extra space fall above and below. The piece stayed complete. The tag stayed in the tile. The photograph was still a square, which is all the painted grid requires. The added space had to come from this dock. Our back wall is scuffed grey, with a darker band where the old fire door used to be. If I filled the new top and bottom with a clean white, the piece looked as if it had been cut out and pasted onto a form. I sampled a quiet area of the actual wall and extended that. Where a work light had left a soft falloff, I used a gentle blur of that same grey rather than a hard band of one averaged color.
I also kept the original wide files. The reprints were made from those originals, not from the already-cropped squares. That felt fussy until a colleague asked whether the third-act flat had shown the repaired corner, which sat just beside the tag. The cropped square had lost the corner and, with it, the house mark. The wide original still had both. I made a new square from that file, with the tag and the repair both inside the tile, and replaced one print instead of calling the whole door a loss.
The door is read at arm's length, under the dock work lights, which are colder than the laptop screen. A tiny export blown up for print turned the lettered cue number into a soft smudge. I now export a moderate square and tape a proof on the actual door before I send the set to the printer. A tag that looks generously included on a screen can sit against the black painted border of the grid, or disappear under the small title strip I letter along the top of the sheet. The proof is the door, not the screen.
The tool I use for that step is deliberately small. I want to drop the wide photograph in, keep every edge of the subject, and take a square away, before the next get-in starts. For that narrow job, make image square without cropping is the page I kept open on the dock laptop. It described the work I was actually doing: making a square from a wide still without cutting the rigging tag off the side. It runs in the browser, which matters on a machine that is not supposed to accumulate software, and it lets me choose a padded square — a sampled color, a soft fill from the wall, or a simple border — instead of a cut that throws the house mark away. It will not invent sharper lettering than the camera captured. It will keep the tag in the picture long enough for a rigger to read it at the door.
Once the corrected tiles were up, a colleague asked only that we cool the top and bottom fill a little, because the work lights make our grey wall look slightly warmer in print than it does in the dock. I adjusted the sample and reprinted the sheet. The tags were still there. The next late cue could be answered by pointing at a tile, which is the entire point of having the door.
I left a short note on the inside of the frame rail: do not center-crop these stills; the tag lives at the side; add canvas from the real wall; proof the square on the actual door before printing. I did not keep the first cropped set in the folder that goes to the printer. Those files are useful as a reminder of what went wrong. They are not dock tiles.
If you keep a wall of flown-piece stills, a rack of tagged flats, or any grid that has to stay square while the identifying mark lives at the edge, look at that edge before you accept the crop. If the tag, the cue number, or the house mark is there, do not cut. Add canvas from the real background, proof the tile where it will actually hang, and only then call the door finished. The picture still has to carry the mark that makes it that piece and not the one beside it.